ModooTronix Products " MHF-R301R "

1. Installation for Hands Free Car Kit

1.		Select a safe and suitable location in the car to attach a magnetic Mobile Phone holder.
2.		Clean both the back of your mobile phone and the surface where the magnet holder will be attached, with the provided cleaner. Wait until completely dry before attaching.
3.		Attach a metal sticker on the back of your Mobile Phone.
4.		Attach the magnet holder in the car where you want to locate your Mobile Phone. (Recommended to safely put 3M sticker over the flame of portable gas lighter for 3~5 seconds to make a stronger adhesion)
5.		Install the ModooFree PLUS on the existing mirror by using the adjustable spring-loaded clips on ModooFree PLUS's back.
6.		Clip Microphone to the sun visor. Install Microphone as close to the driver as possible, in a place with as little wind noise or air movement as possible, for clearer sound.
7.		Plug in both PWR Jack (1) and PHONE Jack (2) on the upper right side of ModooFree PLUS.
8.		Plug in D.C power cable from ModooFree PLUS to the cigarette lighter.
9.		Plug Hands Free Cable (or GSM Audio Adaptor) to your Mobile Phone. Note: If your phone does not have a 2.5mm earphone jack hole, be sure to connect using a GSM audio adaptor. Audio Adapter is optional - Don't forget to purchase an audio adapter suitable for your Mobile Phone, from your ModooFree PLUS retailer.
10.		Fix and hide the cable around the windscreen and under the dashboard by using the fixing clips provided. Ask your retailer to assist you if you are having any trouble.
		◎ Caution while installation 1. Install where it does not block the driver's view and is in easy reach 2. Install microphone where there are minimal wind 3. Install microphone as close as possible facing towards the driver's mouth 4. Do not apply electric shock or stress to the product 5. While placed in direct sun light in the summer, the product might not function properly, so wait for the product to cool off before usage. 6. There will be no A/S for damage by dismantling or rebuilding the product.

> Product Constituents (Hands Free Kit)

>> User's Manual

    1. Power connection and turn on
        Plug in D.C. power cable from ModooFree PLUS into the cigarette lighter.

    2. To make and receive a phone call
        - press the number you wish to call and press "SEND" button of mobile phone.
        - to receive a phone call press "SEND" button of mobile phone when the phone rings.

    3. How to control volume
        Depending on the kind of the cell phone, the volume may differ, but adjust the volume for
        a pleasant usage in the car. (If the reception on the phone is weak, the sound may be static)

    4. Recording / Playing
        - To record press "REC" and when finished press "PLAY".
        - To play press "PLAY", and it will stop at the end of the message.

    5. Private phone call
        - Plug your earphone to the 2.5mm hole of ModooFree PLUS, then it is possible for a private phone
           call with your earphone set.

2. Installation for Reversing (Parking) Sensor Kit

Attach the ModooFree PLUS to the existing rear-view mirror in the car.

Install the control box at the left or right sides of the rear seat beyond the reach of passengers' hands.

Pull the main cable out of the windshield or pedal and connect it to the control box.

Connect the sensor cable and the power cable to the control box.

Use the cable-tie to organize the loose cables.

> Product Constituents (Reversing Sensors Kit)

1) Attach Type

☞ Organizing the Sensor Cable
	After attaching the sensor, attach the mount to the trunk and fix the sensor cable with the cable tie. Then, pull the sensor cable to one side of the trunk and put it in the control box.

☞ Installing the Attach-Type Sensors
	Apply the Two-sided tape to the sensor attachment. Attach the sensor to the trunk or rear lights at about 50-80cm(20"-32") (normally 60cm(23.5")) from the center of the car. ※ The sensor may be positioned upside down.

☞ Connecting the Power Cable

Connect the power cable. Generally, black cables are (-) in vehicles. In the case of the ModooFree PLUS Cable, do not peel off the cable - covering connect it using a line connector. ※ Caution - Beware of the (±) polarity.

☞ Use of the Line Connector

              b. Put up the power cable in the line connector as "a".
              c. Press the clip with a long nose plier.
              d. Close the door of line connector.

☞ Attaching the Alarm



Fix the connector with the control box label at one side of the alarm cable (7m) to the control box connector.

2) Bumper-Insert Type


		1. Mark the areas needed to cut holes at 250-400mm to the left and right from the center of the car using a measuring tape and a pen. (Cf: Mark vertical/horizontal.) ※ Generally, the trunk-lock ring correlates with the center of the bumper. Otherwise, make a mark at the center of the license plate.

2. Cut the marked positions.

※ Caution
  - Beware of the cutter blade during cutting.
  - Cut all materials beneath the bumper including urethane,     beam and styrofoam.

   (Cf: The urethane, beam and styrofoam should not touch
          the sensor body.)

3. Insert the sensor wire through the bumper.
Pull the wire inside the trunk through the body reserve hole. Make the wire and other cables tidy.

※ Caution
The R angle also should be vertical / horizontal at center when viewed
from the side of the bumper.

☞ Connecting the Power Cable

Connect the power cable. Generally, black cables are (-) in vehicles. In the case of the ModooFree PLUS Cable, do not peel off the cable - covering connect it using a line connector. ※ Caution - Beware of the (±) polarity.

☞ Use of the Line Connector

         b. Put up the power cable in the line connector as "a".
         c. Press the clip with a long nose plier.
         d. Close the door of line connector.

☞ Tools required for product installation

☞ Detection distance

☞ Attaching to Other Types of Vehicles (For trucks and tow trucks)

      > It is better to arrange the cables along the left side of the frame (by the driver's seat).
      > Make certain that water cannot contact the sensor while driving.
      > The main cable should be long enough to compensate for the contours of the driver's seat.
      > The main cable should be kept away from the engine, if possible.

Bracket Attachment

Bore two holes on the left and right sides with a drill, so that the bracket can be fixed with screws.

Attach at the center for a 1-ton truck, and at the rear gutter for a larger truck.

>> Caution

	Do not modify the product.
	Use the third-level alarm only when the obstacle is located in straight line from the vehicle.
	Attach the sensor level with the ground surface.
	Keep water away from the alarm (ModooFree PLUS)
	Thin rods or objects, objects with a high tint angle, and sound-absorbing objects cannot be detevted.
	Beware that the power cable or sensor cable may be cut if excessive force is used during installation.
	The area just under and to the right and left ends of the rear bumper cannot be detected.

>> Warranty

        1. A six months warranty on our " ModooFree PLUS Hands Free Car Kit ".

        2. We guarantee strict quality control and inspection.

        3. In case of trouble under regular conditions, return to the store where purchased or we will repair according
            to the warranty.

      4. Warranty does not cover:
            1) Mis-use        2) Re-Assembly        3) Unapproved current sources       4) Out of order due to Force Measure